Avionics Electrical Technician First Class (AET1) SWE Practice Test

These questions are part of the practice quiz. Start practicing

• The initial requesting unit has sole authority to decide what?
• The second and third digit of a TCTO number are used to identify what?
• If electrolyte splashes into the eyes, what is the recommended first aid procedure?
• Which document tracks all serial-number tracked components on an aircraft?
• To prevent fuel starvation due to ice in the fuel system, which item is mandatory?
• Which document contains salvage provisions when appropriate?
• Deficiency reports resulting from HC - 130 Programmed Depot Maintenance ( PDM ) other then ARSC shall be prepared in message format by the receiving activity not later than how many days after receipt of the aircraft ?
• What type of tools shall be used near open fuel cells or taken into the fuel cell?
• Which organization is generally the most current source of recovery / salvage information?
• Which tag is used to indicate an unserviceable item remains attached through processing until serviceable?
• In the six-conductor aircraft service cable, how many conductors are used for power?
• What is the NMCS target percentage?
• What does NMCL stand for?
• Coast Guard Aviation Units aircraft are required to be bonded to what during fueling and defueling operations?
• SAMI stands for which maintenance instruction?
• What angle in degrees should be set between axes on lathes and milling machines?
• For water recovery of Coast Guard helicopters, which assets are desirable to use?
• Which duration applies to the retention of all records maintained by the Aviation Confined Space Entry Program Manager?
• TIMI stands for which maintenance instruction?
• Approved static grounds purpose is to conduct what with electrostatic charges and stray electrical currents?
• This may be prepared when a directive or situation dictates that specific work must be performed on a one-time basis. The work will be completed on one aircraft model or piece of equipment and will not require further action.
• When do you pre - tin MOS devices leads ?
• Who is responsible for reviewing the CO's reports in AMMIS to ensure assets are turned in expeditiously and properly?
• Which system provides bonding during fueling/defueling?
• Grounding requirements for portable electronic test equipment are specified by which code?
• How are changed pages identified in a technical publication?
• This bar coded tag is attached to and identifies equipment and the location of the equipment while in maintenance processing at ALC.
• What shall be used to request an Authorized Chemical Use List change?
• Who is responsible for ensuring that data contained in the ILSP is current?
• Suggestions for revisions to Maintenance Procedure Cards should be submitted on which form?
• A written report of all salvage / recovery challenges should be submitted to CG-41 via the chain of command within how many days?
• The ventilation in nickel-cadmium battery shops is designed to provide how many air changes per hour?
• What is the required electrical condition for all equipment that comes in contact with MOS devices?
• These are normally distributed in a message format and will require immediate action?
• Which Not Mission Capable status corresponds to unscheduled repair work?
• Provisions for salvage, where appropriate, shall be addressed in which plan?
• This priority will be filled if there are more than five parts on the ALC shelf.
• Not Mission Capable Total (NMCT) is derived from which components?
• Which of the following is included in the criteria for USCG weight and balance computations?
• ACMS is the centralized database used to track avionics maintenance actions for what purpose?
• This form will be attached to all parts or components that fail to meet its warranty or mean time schedule.
• What is the maximum current the interlock circuit shall draw from the aircraft's 28 VDC supply?
• As a minimum, units shall print a new MDL how often for each aircraft assigned to the unit?
• The receiving unit of parts pooling must acknowledge receipt of the material via what?
• Where should the taxi signalman position be to direct aircraft for maximum safety?
• What term describes an asset with all subsystems 100% functional and able to operate as designed?
• If an asset is not fully functional due to partial capability, which status applies?
• If corrective maintenance action is delayed beyond 24 hours, what should the asterisked box before the corrective action block contain?
• Hot refueling operations are not allowed within how many feet of any building unless operating under a waiver from CG-41?
• Which battery technology uses a potassium hydroxide electrolyte?
• Electric cargo trucks shall not be operated within how many feet from aircraft during fueling or defueling operations or in the event of a fuel spill?
• Which months are designated for semi-annual publications audits?
• Material used to support the Turbomeca Arriel 2C2-CG engine is which type material?
• Aeronautical support equipment costing more than $250 but less than $3500, with ALC providing initial provisioning but not subsequent replacement or repair, is which type material?
• Who provides for and schedules the PDM of aircraft according to established standards and when required, the repair of aircraft due to crash damage, accelerated deterioration, or similar items?
• On collet-equipped jacks, the collet shall be kept within how many threads of the lift tube cylinder during raising and screwed down firmly to the cylinder after jacking is completed to prevent settling?
• The electrolyte in vented nickel-cadmium batteries is a strong solution of which chemical?
• Type 7 material is used to support which engine?
• Aeronautical and avionics material managed by AICP Elizabeth City is divided into___ type classifications according to price and/or source to determine the kind of control that will be used in its management?
• Aeronautical equipment (e.g., engine, blade, and prop slings / lifting devices) shall be tested in accordance with what?
• Who is required to develop a suitable program for the repair and calibration of electronics test equipment?
• Special metal foil lined packages , conductive foam , conductive plastic packages , or special shorting sockets / connectors may be used for what ?
• Can you pour water into electrolytes?
• Who may authorize a one-time purchase of chemicals not contained on the Authorized Chemical Use List to meet operational commitments?
• What level maintenance is devoted to the repair (not overhaul), test, and return of serviceable status of unserviceable aeronautical components and equipment?
• All solvent soaked cloths or waste should be disposed of in which container and removed from the work area?
• After servicing the LOX system, allow it to stabilize (vent) for at least how long before use, buildup, or reading gauges?
• What does Paper logbook Section 2 contain?
• What information is included on the markings for certified static and power grounds?
• Detailed guidance on management and reporting of flight orders for enlisted personnel is contained in which publications?
• Which unit does not require a Green Tag to stay attached through maintenance processing until serviceable?
• This computer generated report lists all serial number tracked components on an aircraft or major assembly?
• Discrepancies on Mission Generated Maintenance Records (pink sheets) should not remain deferred for longer than ___.
• The post-flight inspection frequency ranges from once a day to once per week depending on what?
• What is the primary purpose of the Commandants Aeronautical Engineering Logistic Compliance Inspection visits?
• Mission generated maintenance records are recorded in which color?
• What information is printed under the basic Technical Order date on the TOPS title page?
• The maintenance level described as routine day-to-day upkeep performed by shop facilities is which?
• Which term describes items whose failure could cause an uncommanded engine shutdown or catastrophic aircraft damage?
• Paint storage must be isolated from which area?
• Who should be notified to inert a large fuel spill?
• Which of the following best identifies the Product Quality Deficiency Report Tag?
• During fueling operations, which equipment must be shut down?
• Units are encouraged to move obstructions outside how many feet of the hot refueling area through normal attrition?
• The routine hazardous material review must confirm procurement conforms to which list?
• This form will be attached to all material that has been determined irreparable or not suitable for aircraft use ( scrap parts or material ).
• The Aviation Confined Space Entry Program Manager shall maintain administrative requirements including reports and logbooks. All records shall be maintained for how long?
• Which of the following statements is true about ATA specification 100 publication contents?
• If the output disconnect is closed when the 28 VDC is lost, the disconnect shall open within how many seconds?
• How are dates recorded according to the document?
• What is the typical distribution format for Interim Rapid Action Changes (IRAQ)?
• The reverse side of a PQDR tag commonly contains which field?
• Aircraft fuel tanks are a permitted confined space as defined in which manual?
• Which container is specified for disposing of solvent-soaked rag waste?
• Who designates CALFAC facilities?
• TCTO kits requiring 4 or less man-hours for incorporation will not be issued within how many days of scheduled aircraft PDM induction dates?
• Special handling procedures for MOS, all power supplies should be checked to ensure that excessive voltage transients of what do not occur when systems are energized or de-energized?
• When shall radar and radio transmitting equipment not be operated on aircraft?
• Thruflight inspections are performed as a turnaround inspection prior to takeoff on the second and subsequent flights of the day for which aircraft types?
• Material shall be shipped to ALC with the appropriate documentation within how many days of removal from service?
• What shall taxi signalmen use when guiding aircraft at night?
• What are the two main categories of Scheduled Maintenance Actions?
• What is the minimum number of people needed to tow a HC-27, and H-144?
• What is the objective of Component Repairs?
• Who is responsible for technical responsiveness to field level Aviation Life Support Equipment maintenance managers?
• What is the ALC's mission?
• What condition code indicates unserviceable material?
• Prototype installations are authorized by which office?
• Which statement best describes the components and height of a standard railing?
• Detailed guidance on management and reporting of flight orders for enlisted personnel is contained in which publications?
• The Maintenance Preflight Inspection is accomplished prior to the ______ and remains effective for ______ provided no subsequent maintenance has been performed.
• Material used for tagging equipment should be twine or other soft material. Do not what?
• Which deficiency report standard form is used for quality deficiencies on all DOD owned material?
• All changes, supplements, RACs, etc., to technical manuals will be incorporated into the applicable manual within how many working days?
• Nickel - cadmium battery shops will be mechanically ventilated to provide how many air changes per hour in order to ensure the removal of any hydrogen gas?
• How long is AFTO 781J (Manual entry or computer spreadsheet) maintained for?
• Who would oversee the overall safety and execution of a Coast Guard aircraft recovery and salvage operation?
• Routine maintenance and replacement of component parts on a required basis is a unit responsibility funded by unit _____.
• On the back side of a PQDR tag, which field is used for narrative comments?
• Who should be in complete charge of the towing team and supervise, normally in front of the tow vehicle?
• Normally a technical order is revised when the pages affected by existing changes constitute what percent or more of the technical order?
• The Thruflight Inspection requirements are accomplished as a turnaround inspection prior to takeoff on the ______ on selected types of aircraft.
• Generally who is desirable and should be used for water recovery of Coast Guard helicopters?
• Outside jacking wind velocity is not to exceed what?
• Where is oxygen servicing of aircraft accomplished?
• The primary directive for Coast Guard fueling operations is what?
• Which document is the primary directive for Coast Guard fueling operations?
• Who is the point of contact for Request for Technical Assistance messages from field units?
• What are the preferred terms fir RFI and NON-RFI?
• The ALSE Prime Unit receives tasking from which organization?
• During normal operations , maintenance personnel should be scheduled based on a goal of a ____ Maintenance Shift Time workweek.
• Under which condition is fuel sample storage not required?
• Which type material covers aeronautical support equipment costing more than $250 but less than $3500, with initial provisioning by ALC but no subsequent replacement?
• Which tag is used to transport serviceable equipment and identifies the item as ready for use?
• Which maintenance actions, in message format, are used for rapid dissemination of information, generally of an urgent or safety-of-flight nature?
• Who is the ALSE prime unit?
• Which color tag is used for irreparable scrap parts?
• Which method must never be used to remove burrs, chips, metal cuttings from machines, work tables, stands, and floors?
• Which field would typically appear on the reverse side for free text?
• Halon does not have what?
• Which tag identifies serviceable equipment?
• Aeronautical material, less avionics, with a unit cost of less than $250, easily procurable from an OGA or commercial source, with units setting allowance quantities and procuring material using the AFC 30 fund, is which type material?
• In JOAP, the spectrometric oil analysis is associated with which designation in parentheses?
• Which form is used to submit recommended changes to flight manuals?
• Certain major electronic shops designated by the district commander as CALFAC may be utilized for the repair and calibration of avionics test equipment when that facility is traceable to the National standard and when calibration and repair will not exceed how long?
• Who is responsible for overall management procurement and the Aviation Inventory Control Point (AICP) for aircraft ALSE avionics support equipment and common support equipment?
• What are the two parts of the six-conductor aircraft service cable?
• What does the green tag indicate during maintenance?
• Hangar deck certified power grounds should be tested to the current standard of less than how many ohms?
• Deficiency reports for aircraft initial delivery from the manufacturer shall be submitted on a _______.
• Containers of not more than how many gallons are used for storing paints and dopes?
• The battery servicing facility workspace temperature shall be maintained at which value?
• Proposed changes to aircraft software shall be submitted to ACCB.
• Which statement is true regarding the NMCS target example?
• New construction is prohibited within how many feet of the hot refueling area?
• How many people are required in the cockpit for all engine starts and run-ups?
• AICP stands for which term?
• Which organization determined that grounding of aircraft during refueling has no effect on equalizing static potential?
• The TOPS numbering system uses a specific sequence; what is the first TOPS number assigned to a TO's page supplements?
• What should anyone in the spill area do when a large spill occurs?
• Which maintenance list tracks maintenance due items based on hours, cycles and landings?
• What identifies enlisted billets by skill and knowledge requirements and is assigned after training and professional accomplishments?
• How many people are required to service the aircraft with gaseous oxygen?
• Which field would you expect to find on the back side of a PQDR tag?
• In hangars that house fueled aircraft, the minimum distance above the floor for all electric power tools and regulators is:
• After completion of a maintenance instruction, for how long should it be canceled and filed?
• In aviation facility hazardous material controls, the procedure to routinely evaluate procurement, storage, and use must establish review intervals. What are the required review intervals for shop storage and for supply storage, respectively?
• If you need to add supporting comments to a PQDR tag, which back-side field is intended?
• Which of the following best describes the restriction on performing maintenance actions early?
• Post-PDM memorandum report deadline after aircraft acceptance?
• When is the postflight inspection accomplished?
• What is the name of the report that maintains a record of significant maintenance actions on serial-number tracked items?
• Flight line static grounds should be tested to be less than how many ohms?
• In the aeronautical materials management, what factor determines the type classifications?
• What term describes a page that supplements an existing Technical Order page and shares the same base TO number?
• What methods are approved for dust control in Coast Guard ALC procedures?
• Who will review all requests for proto-typing of chemicals and approve each specific chemical application on the aircraft?
• Who defines the minimum towing team size in congested areas?
• ACMS stands for what?
• Which aircraft requires the largest minimum tow crew?
• Allowances for Avionics Support Equipment are contained in ___.
• What restriction applies to performing maintenance actions early on scheduled components?
• What gauge wire is specified for the personnel ground device?
• Prior to engine start, what action must be taken to prevent aircraft movement?
• Records retention for field units material requests on form CG-4491 will be maintained for how many fiscal years?
• Who is generally the most current source of information relating to recovery / salvage?
• A TCTO master file will be maintained at each unit through what?
• What is the primary purpose of the back side of a PQDR tag?
• Which NM status indicates the asset is awaiting a critical part?
• Which aircraft types are referenced for the engine start crew requirement?
• How often should covered metal cans be emptied?
• How is aviation breathing oxygen cylinders identified?
• How are all dates recorded on forms?
• What is the minimum letter height used to mark certified static and power grounds?
• Discrepancies on Mission Generated Maintenance Records are identified on what color sheets?
• What is the maximum number of days allowed from the date of failure of a part to shipment to ALC for handling of unserviceable material?
• What is the maximum approved static ground resistance?
• During which inspection are salvage plans reviewed for a unit?
• Provisions for salvage, where appropriate, should be addressed in which plan?
• The Prompt Payment Act requires that ALC pay vendors for shipment within how many days of receipt of the material?
• What color page designates a Technical Order Page Supplement (TOPS) that supplements rather than replaces a TO page?
• AFTO 781J is maintained for how long?
• The MORPT for each aircraft shall be reported to ACMS not later than how long following the end of the report period?
• Which color represents the paper logbook for preflight and servicing records?
• Subsequent Type 1 material transactions are controlled by whom?
• U.S. Coast Guard aircraft are to be what when parked?
• What field appears on the back of a PQDR tag?
• What symbol indicates current changes in the text of a revision that were not previously published as TO changes or supplements?
• Introduction of Fuel System Icing Inhibitor will lower the JP-5 flash point by 4 degrees Fahrenheit and will also inhibit what?
• Before inserting SRUs with MOS devices into test sockets or subassembly circuits , manually hold the SRU and the test equipment or subassembly chassis simultaneously to ensure what?
• Which type material is defined as aeronautical material with serviceable support responsibility by ALC and a unit price of $250 or more?
• Which term indicates the percentage of not mission capable time that should be minimized?
• What is used for the maintenance and audit of Coast Guard Technical Libraries?
• In the personnel grounding device, the clip or clamp is connected in series to what?
• Type 1 material transactions shall be reported to ALC by what?
• The MLHs expended at each unit for ACMS tracked MPCs and the EAL maintenance and servicing forms are approximately what percent for the total maintenance labor hours expended?
• Which section of the paper logbook contains The Maintenance Discrepancy Report?
• What is the backside of the PQDR tag used for?
• CAMI is the acronym for which maintenance instruction?
• What resistor value is specified for the personnel ground device?
• Fuel system icing inhibitor use in turbine fuel is set at what percent?
• What must be done to the ram locking nut on collet-equipped jacks to prevent removal?
• What manual provides detailed information regarding the standard organization for air units?
• How long are paper forms retained after entry into EAL?
• Which phenomenon is prevented by maintaining equal electrical potential in the grounding system?
• This form shall be used for submitting recommended changes to flight manuals ?
• Coast Guard TCTOs (in message format) are used for what purpose?
• Which tagging material is prohibited for equipment tagging?
• What are the Force / Activity Designators assigned to general air stations and to ALC, ATTC and ATC Mobile?
• These are distributed by expedited means to all units under distribution for the publication. Normally involve possible safety of flight or faulty equipment items?
• Which printed directives in MPC format require accomplishment of a specific task?
• Paper logbook section 3 contains?
• Which publication level structure does ATA Spec 100 use to organize contents?
• Which of the following best describes the back of a PQDR tag?
• October publications audit conducted by whom?
• Without the Unit Engineering Officer's approval, how long can corrosion discrepancies remain open (except deployed aircraft)?
• Once a new MDL is printed, what happens with the old one?
• These inspections are designed to provide servicing and verification of the satisfactory function of critical systems and components at frequent intervals.
• What is the purpose of an approved static ground interconnected with aircraft and support equipment?
• Temporary improvised scaffolds of stands may be used if approved by who?
• Completed ACMS Maintenance Procedure Cards shall be retained for how long?
• All MOS devices or Shop Replaceable units (SRUs) with MOS devices not in use should be stored in what type of package, so that all leads, pins are shorted via the package?
• What is the distribution of the AF Form 847 ?
• Avionics material that is either repairable, flight critical, procured from a commercial source of supply, or has a unit cost of $800 or more is which type material?
• Urgent safety of flight material defects are submitted using which format?
• What is the required workspace air temperature in the battery servicing facility?
• Which statement best describes the ALC mission scope?
• Which tag is attached to any part or component that fails to meet its warranty or mean time schedule?
• The asset is undergoing unscheduled repair work. Which NM status is appropriate?
• Who should ensure that planning for and expenditure of assigned funds is consistent with the overall objective of the unit maintenance plan?
• What condition allows the radar antenna to be operated closer to fueling operations than the standard 300 ft limit?
• The radar antenna should not be operated within how many feet of fueling operations unless a dummy load is installed that prevents energizing the antenna?
• During hot refueling, obstructions are encouraged to be moved outside how far from the hot refueling area?
• The postflight inspection is performed after which event?
• The Post PDM memorandum report in no case shall be submitted later than how many days after aircraft acceptance?
• Hazardous waste disposal shall be in accordance with which manual?
• Within how many feet must an aircraft not be taxied from obstructions?
• Consumable avionics material with unit price less than $800 and procurable from OGA is which type material?
• Upon receipt of the part(s), an additional comment stating ____ and _______ shall be added to the PP discrepancy.
• Certified static and power grounds are marked with what?
• In preparation for flyaway operations and periods of non-connectivity, each unit shall maintain a sufficient number of printed forms onhand to enable normal asset flight and maintenance operations for a period of _____.
• Which color tag is used for unserviceable reparable items?
• The ASR is used to capture aircraft / unit operating statistics. An ASR form shall be completed how often?
• If an asset is fully operational and 100% functional, what status applies?
• What is the minimum number of people to tow a HH-65 and HH-60?
• Parts Pending discrepancies must have a non - flight - essential part requisitioned and a part requisition number must be provided within ___.
• Which elements compose a personnel ground device?
• Flight line certified static grounds should be tested to the required standard of how many ohms?
• What remark is entered on the DD-1574 tag when a part is used on multiple aircraft?
• Oxygen cylinder storage shall be separate from fuel - gas cylinders or combustible materials (especially oil or grease) by at least a distance of what?
• What form is used to correct errors in the ILSP?
• Lathes , milling machines , and similar types of equipment that produce cuttings or flying particles should be set at ___ degree angles to each other
• This is a local directive providing instructions for the performance of work which is or may be a continuing nature.
• Storing equipment outside of existing structures within how many feet of the hot refueling area is prohibited?
• Weight lifting devices used at aviation units shall be tested in accordance with what Manual?
• Which Not Mission Capable status corresponds to scheduled maintenance work?
• Fuel spills involving an area of 18 inches or less in any dimension are normally of minor consequence. Ramp personnel shall?
• All MOS devices and assemblies should be placed on a grounded bench surface of what type of material ?
• Hazardous waste disposal shall be in accordance with what manual?
• Which type material includes avionics that are repairable, flight critical, procured from a commercial source, or have a unit cost of $800 or more?
• By how many days after receipt of shipping orders should Type 1 material be shipped?
• Which field on the back side is designated for narrative comments?
• Chronic solvent poisoning is caused by repeated daily exposures for extended periods. Which term describes this condition?
• Which board is responsible for approving changes to the configuration of aircraft software, equipment, or support structure?
• Reporting custodians shall ensure USCG aircraft weight and balance computations at which times?
• Which signaling device is specified for night guidance of aircraft by taxi signalmen?
• If electrolyte is swallowed, what is the recommended first aid action?
• Shipment will be effected within how many hours of receipt of message?
• TriSwap memorandum reports are used to capture discrepancies encountered during which process?
• To perform hot refueling within restricted distance, a waiver must be obtained from which entity?
• Who reviews all proto-typing chemical requests and approves each specific chemical application on the aircraft?
• What is the Type 7 material type?
• When can cockpit personnel apply the brakes during a towing evolution?
• Tools used for servicing nickel-cadmium batteries will be what?
• The unit receiving an aircraft from a transferring unit shall submit a report to the Commanding Officer, ALC, with an information copy to Commandant, CG-41, Transferring unit and ALC in what format?
• DOD has adopted this Quality Deficiency Report as a standard form for use in reporting quality deficiencies on all DOD owned material ?
• In a list of codes for grounding standards, which option corresponds to the National Electrical Safety Code?
• In documenting a deficiency, which back-side field is used for additional notes?
• What does ACCB stand for in the context of aircraft configuration control?
• The heat shrink insulation on the battery tools should be inspected how often?
• What is the distribution of AF Form 847?
• Completed MPCs will be retained for how many days?
• Paper logbook section 4 contains?
• The decision to parts pool rests solely with whom?
• After last alcohol use, how long must maintenance personnel abstain before performing maintenance activities?
• No maintenance shall be performed on systems covered by warranty except as authorized by their ?
• Aeronautical material under individual serial-number management by ALC for aircraft engines, high-value components, special configuration control, or critical supply is which type material?
• What type of fire extinguisher is specified for use during a minor spill response upwind?
• Ensure a serviceable 125/150 lb wheeled PKP fire extinguisher or equivalent is placed within ___ of the LOX servicing operation.
• Hangar and shop fire extinguishers shall be either CO2 and dry chemical, water and foam, ABC and BC, or Halon and Water. Which combination is specified?
• Flight safety maintenance documents are recorded in which logbook color?
• Which tag should be used specifically to document a product quality deficiency impacting a part?
• PQDR stands for which tag?
• If a CALFAC is used for repair or calibration, the facility must be traceable to what standard?
• COAST GUARD AIR STATIONS AND OPERATIONAL AVIATION UNITS WILL ONLY USE __________PRIMERS.
• Who designates engine run-up areas in accordance with airport procedures?
• For all engine starts on MH-60 and MH-65, how many people shall be in the cockpit?
• Aviation ground support equipment bowsers procured or constructed after 1 January 1995 must meet which standard specification?
• What term refers to documents issued to augment or change data in basic T.O.s that cannot be included with individual change pages?
• ATA specification 100 publication contents are organized on four levels; The Unit / Subject numbers are not Preassigned; these numbers and their sequence may be selected by who?
• What color tag is used for an unserviceable item that is condemned or scrap?
• Which document lists equipment shortages that must be rectified before transfer?
• When are fuel samples storage not required?
• During fueling or spill, electric cargo trucks must maintain at least how many feet from aircraft?
• This TriSwap memorandum report covers discrepancies encountered during the first how many days?
• IRAQ stands for Interim Rapid Action Changes. What is the main purpose of IRAQ?
• Under no circumstances should what type of brush be used for cleaning batteries?
• Units salvage plans will be reviewed during the unit's _______.
• Which of the following describes the purpose of ventilation in nickel-cadmium battery shops?
• Salvage plans shall be maintained in a current status where?
• Which months are the semiannual audits conducted?
• What is the only aircraft that uses the AFTO 103 form?
• What is defined as any part , assembly , or installation equipment containing a critical characteristic whose failure , malfunction , or absence could cause an uncommanded engine shutdown or catastrophic failure resulting loss of or serious damage to the aircraft ?
• What is the typical reason for issuing a RAC (Rapid Action Change)?
• How often is each salvage plan updated?
• Under what condition can maintenance be performed on systems covered by warranty?
• Who shall conduct a monthly review of each aircraft logbook as a quality assurance check of ACMS management procedures?
• Which whistle signal is used to stop tow operations?
• All requests or suggestions for new or additional AGSE shall be made by official correspondence to who?
• The asset is suspended in ACMS by ALC or APO for non-depot related activities. This status corresponds to which NMCS condition?
• Flight safety maintenance documents correspond to which color in the paper logbook?
• Proposed changes to aircraft software, equipment or support structure shall be submitted to who?
• All unit avionics shops are required to maintain in-house capability for avionics repair at what level?
• Which brush type is prohibited for cleaning batteries?
• The purchase of Halon fire extinguishers for flight line, hangar and shop use is what?
• The paper logbook color used for mission records is which color?
• Which body reviews and recommends changes to standard aircraft configuration?
• All acceptance testing, minimum performance testing and fault verification shall be entered into where?
• What is the minimum number of people needed to tow a C - 130?
• What components make up a standard railing?
• Fuel samples shall be kept for how long?
• Which document governs testing of aeronautical equipment such as engine, blade, and prop slings / lifting devices?
• Who is responsible for procuring General Purpose Electronics Test Equipment used for station maintenance and all specialized Electronics Test Equipment for non-avionics use?
• Recovery and Salvage of Coast Guard aircraft is the responsibility of who?
• Static grounds are tested how often?
• Identify the field commonly located at the back to capture notes.
• In hangars housing fueled aircraft, the minimum clearance above the floor for electric power tools, switches, and related devices is?
• Fuel spills over 50 square feet in area or of a continuing nature. Ramp personnel ?
• The TCTO numbering first part or number will always be what?
• These inspections, Operations, Calendar, hourly, Cycles and Landings, ensure a thorough examination of all systems and components on a scheduled basis.
• What forms of protection should be installed to eliminate injury when machinery and powered transmission equipment are not guarded by design?
• The physical transfer of an aircraft will take place upon completion of the mandatory joint inventory by the transferring and receiving units. Shortages of equipment on the OPNAV 4790 are unacceptable. If shortages exist at the time of transfer, the transferring unit has ___ days to rectify the shortage?
• ILSP stands for which document?
• Which organization is responsible for ALSE avionics support equipment procurement?
• Which gas is used for aircraft servicing?
• Changing or adding part numbers to any Coast Guard Illustrated Parts Catalog, or Illustrated Parts Breakdown may be incorporated directly from what form?
• NFPA has determined regarding grounding aircraft during refueling/defueling:
• When reporting an aircraft transfer, who should receive an information copy of the memorandum report?
• Once an item is declared unserviceable material (condition F) the practice of using it as a source of spare parts is ?
• Which documentation system is used to acknowledge receipt of pooled material?
• What are the two types of solvent poisoning?
• Form CG-4491 is used for what purpose?
• What is the lead-time for planning, budgeting and procurement of major items of GSE?
• Class D refers to which maintenance category?
• Which unit is designated as the ALSE prime unit?
• General air stations use Force / Activity Designator II; ALC, ATTC and ATC Mobile use III. Which option best describes this pairing?
• Which priority will be filled if there are more than two parts on the ALC shelf?
• All uninstalled serial-number tracked components must be accompanied by a current copy of which report?
• Which offices are responsible for reviewing and expediting asset turn-in?
• Vacuum dust collecting surfaces must be performed at least how often?
• Each unit will conduct semi-annual Pubs audits during which months?
• What word should not be written on serviceable and unserviceable tags?
• Other than routine message how else must Type 1 material be reported?
• Which acronym represents the program that monitors wear metals in lubrication fluid to assess mechanical wear?
• Fuel spills not over 10 feet in any dimension or not over 50 square feet in area and not of a continuing nature. Ramp personnel shall?
• Who normally performs trial installations?
• Which entity is the point of contact for Request for Technical Assistance messages from field units?
• Jacking- All collet-equipped jacks must have what feature to prevent removal?
• This form shall be used to recommend corrections of errors which affect the meaning of information procedures contained in COMDTINSTs , technical manuals or ACMS.
• Which program is used to monitor wear metals in lubrication fluids to assess engine wear?
• Scheduled Maintenance Actions are defined under what two categories?
• Which manual takes precedence for avionics equipment when the Aeronautical Engineering Maintenance Manual and the Coast Guard Electronics Manual differ?
• The fourth and fifth digit of a TCTO number represents what?
• Which program monitors wear metal concentrations in lubrication fluid to assess enclosed mechanical systems?
• Which tag corresponds to the Product Quality Deficiency Report Tag?
• Prior to adjusting the electrolyte level, the battery must be charged and allowed to sit for how long?
• If battery electrolyte gets into the eyes, how long should you flush with water?
• ASR information may be entered into ACMS up to a MAXIMUM of how many days after the form date?
• What term describes an asset when a specific system is not meeting 100% of designed functionality?
• When an aircraft is being taxied within 25 feet of an obstruction, what safety measure is required?
• Who shall be in complete charge of the towing team and take a position that will ensure surveillance of the towing procedures and performance of other team members, normally in front of the tow vehicle?
• These are certain additional inspections, distinct frequency from routine inspections, which are conditional upon operational environment, specific incidents, or other circumstances requiring inspections?
• Pilots in command of flight verification checks and test flights shall be briefed on procedures and systems to be checked by whom?
• May be prepared when a directive or situation requires that technical information be promulgated within an activity, such as techniques and local policy, which does not direct the accomplishment of specific work at definite intervals, but which is sustaining in nature?
• Which field on the back side is used for notes in a PQDR tag?
• The level of corrective maintenance authorized at the unit level is defined where?
• Entry Authority certification is valid for how long?
• Participation in Joint Oil Analysis Program (JOAP) or Spectrometric Oil Analysis (HU-25) is what for certain components and optional for others?
• In EAL usage, which color is used for special inspections?
• After final approval of a CG-22, where is it archived?
• Who shall establish and maintain preventive maintenance programs to ensure that SE will meet projected service life requirements?
• If an aircraft type avionics ILSP has not been published, the level of repair authorized at the unit level shall be in accordance with what?
• Which priority is used for immediate shipment when there are parts on the ALC shelf?
• Which color is used for logbook reviews in EAL?
• On the reverse side of a PQDR tag, which field is used for free-text information?
• After printing a new MDL, the old MDL may be...
• Proposed changes to aircraft software shall be submitted to whom?
• The minimum number of people on a towing team when towing aircraft in a congested area is defined by whom?
• Which position is responsible for establishing preventive maintenance programs at a unit?
• Which manual governs avionics equipment and avionics support equipment when there is a difference?
• Each unit will conduct semiannual audits during the months of April and October. What must be signed showing accomplishment of this task?
• Which field on the back side captures explanatory text about the deficiency?
• Which of the following is the Air Operations Manual designation?
• Is there a centralized data base of avionics maintenance actions that enable tracking of avionics components through their entire life cycle?
• TCTO kits requiring more than 4 man-hours for incorporation will not normally be issued within how many months of the scheduled aircraft PDM induction date?
• The April publication audit will be conducted by whom?
• During towing operations, which whistle signal shall be used to signal stop?
• Aeronautical material for which ALC has serviceable support responsibility, with a unit price of $250 or more, procured from a commercial source, flight critical, and reparable is which type material?
• NMCT is an acronym used in this material. What does it stand for?
• A TOPS page is filed in the Technical Order (TO) where relative to the affected page?
• What are the only Coast Guard vessels considered adequate for recovering an HH-60 helicopter?
• Which type material uses the AFC 30 fund and allows units to set their own allowance quantities?
• Hot refueling operations are not allowed within how many feet of any building, unless waivered from CG-41?
• Which pins of the aircraft service cable must be connected for the 400 Hz external power interlock to energize the output contactor?
• Maintenance errors contribute to approximately what percent of DoD and commercial aviation mishaps?
• Failures or unsatisfactory conditions of CSI/FSCAP noted by air stations shall be reported by what means?
• In a spill not over 50 square feet and not continuing, after posting a fireguard upwind with a foam-type or halon-type extinguisher, what is the required action?
• Who may authorize taxing of aircraft without a taxi signalman, providing the ramp has clearly defined taxi lines and parking spots?
• Which Not Mission Capable maintenance status indicates scheduled maintenance?
• This form will be attached to an unserviceable item that is nonreparable at ALC and will be sent to an outside vendor or manufacturer for repair.
• A new MDL should project all scheduled maintenance for calendar and hourly tasks for how long an operating period?
• Who is responsible for reviewing paper logbook forms and how often must the review occur?
• Which form is used to capture aircraft / unit - operating statistics. An ASR form shall be completed how often?
• Supply Item Change Records (SICRs) are used to document changes to which Coast Guard publications?
• The mission record is associated with which color?
• Identifies enlisted billets by specific skill and knowledge requirements and are assigned to eligible personnel following appropriate training and professional accomplishments?
• Which tag is attached to an unserviceable item during maintenance processing?
• Paper logbook section 1 contains?
• Refresher MRM training is an ____ requirement for all rated enlisted aviation maintenance personnel, engineering officers, student engineers and maintenance officers.
• Personnel are restricted from performing aircraft maintenance or any aircraft maintenance related activities for ____ after last alcohol use.
• Engine run-up areas are designated in accordance with what?
• Acute solvent poisoning is defined as inhalation of an excessive concentration within a short time. Which term describes this condition?
• Which aviation units shall prepare and maintain a Salvage Plan?
• Which statement is true regarding equipment that comes in contact with MOS devices?
• Which report is used to document any unusual work required for aircraft scheduled for military or commercial activities?
• Consumable avionics material with a unit price less than $800 and procurable from an OGA source is which type material?
• The battery electrolyte level must not be adjusted until the battery has been charged and allowed to sit for how long?
• Which Not Mission Capable status corresponds to awaiting a critical part?
• What shall be readily available in case of any emergency during any towing operation?
• Who shall ensure that an effective calibration program is implemented for assigned equipment and tooling?
• During taxiing within 25 feet of an obstruction, which arrangement is required?
• Do not deplete an oxygen bottle below what PSI?
• Which color is used for functional check requirements and aircrew warnings in EAL?
• Which section on the reverse side of a PQDR tag is used for additional notes?
• Dates and times shall be recorded in ZULU format on all forms except the _____.
• What is the acronym ACMS used for in this context?
• The _______ of the unit to which a mishap aircraft is permanently assigned has full responsibility for the recovery and salvage of their aircraft.
• What card must be signed showing accomplishment of a semi-annual publications audit?
• The records for CG-4491 material requests are retained for how many fiscal years?
• Engine driven power units shall have what done prior to connecting or disconnecting external power cables to the aircraft?
• Where is the Deferred Maintenance Record located?
• A target aircraft availability of 71 percent corresponds to what NMCT percentage?
• The ACMS code, which the TCTO numbering aligns with, is divided into how many parts?
• Assignment of the Salvage Officer is whose responsibility?
• Paper logbook section 2 contains?
• What shall the towing speed not exceed?
• All other forms in the paper logbook use which color?
• Which organization issues shipment orders for Type 1 material?